Search:

Type: Posts; User: Aviator

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 25 minute(s) ago.

  1. Thread: turbo oil leak

    by Aviator
    Replies
    6
    Views
    2,767

    More than likely, the banjo bolt that holds the...

    More than likely, the banjo bolt that holds the oil supply pipe to the top of the turbo, has loosened off. This will make oil piss out all over the back of the engine and then undercoat the bottom of...
  2. Replies
    3
    Views
    1,477

    Volvo doesn't make "winter" wiper blades.

    Volvo doesn't make "winter" wiper blades.
  3. You need a new turn signal stalk. This is a...

    You need a new turn signal stalk. This is a fairly common issue with the P3 XC70s. It's plug and play....no programming needed.
  4. Replies
    6
    Views
    1,038

    It goes on the end of the long bolt that goes...

    It goes on the end of the long bolt that goes through the top engine mount.

    Dave.
  5. Replies
    3
    Views
    668

    I asked because it may be your trailer lighting...

    I asked because it may be your trailer lighting or wiring that's causing the issue. ;)

    Dave.
  6. Replies
    19
    Views
    2,343

    Good to hear it's sorted out for you. Dave.

    Good to hear it's sorted out for you.

    Dave.
  7. Replies
    6
    Views
    1,235

    Probably the sway bar links are worn out. They...

    Probably the sway bar links are worn out. They either get a lot of play in the lower ends, or they go "dry" inside the ends and end up making creaking sounds. I'd start with those first. Also. lately...
  8. Behind the bumper cover is what's called the rear...

    Behind the bumper cover is what's called the rear section in which the "attaching plates" are held. These are what you are describing, and they can be purchased seperately from the rear section. Left...
  9. Replies
    3
    Views
    811

    There's no set way to take the pan down. I try to...

    There's no set way to take the pan down. I try to lower the transmission end a bit and feed the pan down on an angle and then straight down. The mouth of the oil pickup will catch in the pan. Just be...
  10. Replies
    8
    Views
    3,286

    Front to back is the correct way, however, Volvo...

    Front to back is the correct way, however, Volvo doesn't recommend rotating tires now.

    Dave.
  11. That's a healthy PCV system!! Dave.

    That's a healthy PCV system!!

    Dave.
  12. Replies
    8
    Views
    5,126

    What did you test the BCM with?

    What did you test the BCM with?
  13. Replies
    3
    Views
    668

    Could be a problem with the socket and/or the...

    Could be a problem with the socket and/or the lamp assembly. If the socket isn't seating right on its contacts, it will arc at the voltage contact and that will pop a fuse as well. I believe you also...
  14. You don't know that for sure though. You could be...

    You don't know that for sure though. You could be at -.2kPa which is the threshold for PCV overhaul. You could even be at -.3kPa. See, that's the importance of using a tool that has units of...
  15. That's correct. The tube sinks into the top of...

    That's correct. The tube sinks into the top of the pan by about 10mm. The stick extends beyond the bottom of the tube, and dips into the oil in the pan.

    Dave.
  16. Never any at the top hole in the block. It's a...

    Never any at the top hole in the block. It's a much bigger hole than the lower one. You might see a little bit of crud hanging around it; just scrape it away and wipe the hole....kinda like wiping...
  17. Replies
    19
    Views
    2,343

    You're welcome. I'm not sure that you can get the...

    You're welcome. I'm not sure that you can get the deflector on its own though as a stand alone part; pretty sure it only comes in the bearing kit.

    Dave.
  18. Replies
    2
    Views
    606

    Dealer item....PN 9171544. That's the control...

    Dealer item....PN 9171544. That's the control mechanism closest to where the heater core is.

    Dave.
  19. Replies
    8
    Views
    5,126

    From your information it sounds like you need a...

    From your information it sounds like you need a new BCM (brake control module), plus software. I highly doubt there is an issue with a speed sensor in the transmission.

    Dave.
  20. Replies
    20
    Views
    7,093

    It's quite easy to get in on that bolt by using...

    It's quite easy to get in on that bolt by using 1/4" drive ratchet, 10" extension, and short 6 point 10mm socket. It only needs to be loosened a little bit, and the manifold will come right off....
  21. Replies
    19
    Views
    2,343

    Well that sucks. At least it's easy to get in and...

    Well that sucks. At least it's easy to get in and out. If all else fails you can just leave it out. After all, the car came off the assembly line without them, and you've gone this far....Not...
  22. The opening for the lower hole in the block has...

    The opening for the lower hole in the block has to have clear passage to, and through, the square passage/channel that is in the pan (can only be seen with the pan off). As far as this being part of...
  23. No, the subframe doesn't need to be lowered. Pan...

    No, the subframe doesn't need to be lowered. Pan removal is very straight forward. You'll need new oil pan O rings, new oil cooler O rings, tube of sealant to reseal the pan back into place.

    Dave.
  24. Angle the wiper arm towards you. Grab hold of the...

    Angle the wiper arm towards you. Grab hold of the arm and then hold the arm against the glass (like holding someone against a wall with their shirt collar). Put your right hand on the blade body and...
  25. Replies
    8
    Views
    5,126

    Need more information about the car, as well as...

    Need more information about the car, as well as posting in proper English instead of pig Latin.

    Dave.
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4