Search:

Type: Posts; User: Xfingers

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    73

    Might want to spray down the latch mechanism real...

    Might want to spray down the latch mechanism real well with WD40 or similar penetrating oil; you could have some crud buildup. Lube the points on the latch which pivot and move the release handle...
  2. Not on my 02; but included on my 07. I gave it a...

    Not on my 02; but included on my 07. I gave it a try when I first got the 07XC and wasn't terribly impressed. I use the adjustable delay setting on my wipers and sometimes just find it easiest in...
  3. Replies
    1
    Views
    145

    Are you looking for heater core/heat exchanger...

    Are you looking for heater core/heat exchanger removal?
    https://www.volvoxc.com/0/resources/how-to/pdf/heat_exchanger_removing.pdf
  4. Thread: DEM000b

    by Xfingers
    Replies
    10
    Views
    779

    Maybe check back with XemodeX. If it's something...

    Maybe check back with XemodeX. If it's something easy or obvious, they might have some suggestions to check. One of your electrical contacts could be dirty?

    I don't have my VIDA/DiCE up and...
  5. Replies
    11
    Views
    673

    I don't have experience diagnosing ETM issues. If...

    I don't have experience diagnosing ETM issues. If that ETM fuse was blowing, then I guess the ETM electronics were calling for/drawing way too much current. Maybe check all the wiring/connections...
  6. Replies
    49
    Views
    2,472

    "The outside temperature sensors were not working...

    "The outside temperature sensors were not working anyway."

    Does anyone know if this can have an effect on driveability?
  7. Replies
    69
    Views
    5,597

    Oka, can you be more specific when you say "Then...

    Oka, can you be more specific when you say "Then it died." and "Then, it dies again."?
    Will the car turnover and start after it dies?
    Are you using VIDA to troubleshoot your issues? If often will...
  8. Replies
    31
    Views
    1,816

    I don't remember from your earlier threads, but...

    I don't remember from your earlier threads, but it sounds like this 2007 was new to you when you got it with the broken valve? In other words, you haven't been driving it for years and thousands of...
  9. Replies
    2
    Views
    432

    DEM stands for Differential Electronic Module...

    DEM stands for Differential Electronic Module which refers to the Haldex unit of your AWD system. If you have VIDA/DiCE, a scan should tell you if your AWD is working.

    Last fall, I was getting a...
  10. Replies
    3
    Views
    442

    Is the check engine light (CEL) coming on? If so,...

    Is the check engine light (CEL) coming on? If so, you can read the stored code(s) for a clue to what the problem is.
    Maybe you're having issues with the fuel/air ratio mixture? Are any hoses...
  11. Replies
    69
    Views
    5,597

    Any codes? Can you trace it in VIDA?

    Any codes? Can you trace it in VIDA?
  12. Replies
    69
    Views
    5,597

    I remember it being a little tricky getting the...

    I remember it being a little tricky getting the air intake to mate up with TB. I'm not sure how exactly I did it. Would it help to keep the attachment bolts of the TB threaded but very loose so you...
  13. Replies
    12
    Views
    1,606

    In PA a car can pass inspection with the MIL/CEL...

    In PA a car can pass inspection with the MIL/CEL on? Maybe whatever is causing the light to trigger isn't emissions related?

    With VIDA, you can usually read the codes, CLEAR them, and the light...
  14. Replies
    13
    Views
    1,613

    Hopefully someone with more knowledge than me has...

    Hopefully someone with more knowledge than me has a better feel for the different starting requirements of a cold engine vs. a warm one. Different fuel amounts? Longer cranking time? These are just...
  15. Replies
    13
    Views
    1,613

    Does your professional installer have any ideas...

    Does your professional installer have any ideas what the problem may be?

    Does the engine crank/turn over with the remote when it's cold out? If so, how many times or how long?
    How many times or...
  16. Replies
    68
    Views
    4,813

    Seems like early in this thread we suggested you...

    Seems like early in this thread we suggested you may be experiencing shifting problems due to a worn valve body. My car was throwing the P0740 code and going into Limp Mode until I replaced it. Have...
  17. Thread: PCV kits?

    by Xfingers
    Replies
    19
    Views
    1,497

    It helps me to count the notches on the old belt...

    It helps me to count the notches on the old belt between the timing marks before I remove the belt. Then when you put the new belt on, count to make sure you've got the same number of notches between...
  18. Thread: PCV kits?

    by Xfingers
    Replies
    19
    Views
    1,497

    If you've got a new gasket for the throttle body,...

    If you've got a new gasket for the throttle body, you can remove and clean it pretty easily with the manifold off.

    This is the vid that helped me when I had to replace the intake cam seal on my...
  19. Replies
    3
    Views
    491

    I had to replace the temp/pressure sensor on my...

    I had to replace the temp/pressure sensor on my Haldex. At 200k miles, the Haldex oil was very clean so I figured it must have been serviced before I got the car. I also replaced my Angle gear oil...
  20. To remove that top nut from the spring strut to...

    To remove that top nut from the spring strut to take it apart, you're also gonna need a T40 torx bit as a counterhold to hold the bolt while you're turning the nut (or to turn the bolt while you're...
  21. That's a good vid vtl linked to that shows the...

    That's a good vid vtl linked to that shows the various components and locations.

    I replaced my right rear spring a couple of weeks ago which was broken. With the new spring, the car's rear end...
  22. Replies
    68
    Views
    4,813

    I bought a new GM valvebody. I believe it was a...

    I bought a new GM valvebody. I believe it was a type B, my original VB was a type A or maybe blank. As Astro has indicated, to make a B valvebody compatible with a trans which had an original A...
  23. Replies
    3
    Views
    369

    When I did my brakes and rotors a few years back,...

    When I did my brakes and rotors a few years back, some anti-squeal grease packets were provided to apply to my Bosch brake shoes. FCPEuro has a pretty good youtube video on replacing the brakes and...
  24. Replies
    3
    Views
    536

    Is your car throwing any codes/CEL? Possibly a...

    Is your car throwing any codes/CEL?

    Possibly a dirty MAF (mass air flow) filter? Apparently you can test to see if its causing problems by unplugging the electrical connection to it, starting the...
  25. Replies
    68
    Views
    4,813

    I did 3 flushes with new ATF with no improvement....

    I did 3 flushes with new ATF with no improvement. I talked on the phone to a rep with an ATF cooler company and told him my plan to keep the fluid below 60C using a cooler so the trans would shift...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4