Search:

Type: Posts; User: Heath

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Check valve near the fuel pump is faulty allowing...

    Check valve near the fuel pump is faulty allowing the fuel line to drain?
  2. Replies
    1
    Views
    1,583

    Drivers side (L) fog light from my 00 XC $15

    http://imagizer.imageshack.us/v2/640x480q90/911/XjQRBP.jpg

    http://imagizer.imageshack.us/v2/640x480q90/910/3OSch9.jpg


    $15 plus actual shipping from NC 28659
  3. Replies
    6
    Views
    3,618

    My up arrow began flashing and CEL illuminated...

    My up arrow began flashing and CEL illuminated after shifting to 3 while driving up a long grade at approximately 60mph. The only code is P1618. The car is not in limp mode. Our problems seem to...
  4. No limp mode but flashing up arrow and only code is P1618.

    I moved the shift selector to 3 while traveling up a long grade at approximately 60mph. Not long after the flashing up arrow and check engine light appeared. The only code is p1618. I have removed...
  5. Thanks for the info! On what I think is the 2-3...

    Thanks for the info! On what I think is the 2-3 shift (around 30 mph) the transmission shifts then feels as though it boggs and downshifts again immediately. You can feel the car using the gears to...
  6. Is the adaptation adjustment via dealer only? ...

    Is the adaptation adjustment via dealer only? Will the car eventually adapt on it's own?
  7. Unfortunately I do not. I suppose I'll drain a...

    Unfortunately I do not. I suppose I'll drain a bit of fluid and go for another test drive. It seems this is something that should either be required or not be. I don't understand the gray area.
  8. Tranny swap- 99 into 00 xc... is a marrying via software necessary?

    I just completed my swap and went for a test drive. After a mile or so of normal operation the transmission began bogging. It seemed to almost drop off into neutral. I would let off the gas a bit...
  9. Replies
    6
    Views
    2,550

    I am now able to insert the ball bearings into...

    I am now able to insert the ball bearings into the knuckle or cage but I cannot seat them all in the housing and install the cover. It seams as though the knuckle may have to be centered (not...
  10. Replies
    6
    Views
    2,550

    Thank you. I will give it a shot first chance I...

    Thank you. I will give it a shot first chance I get!
  11. Replies
    6
    Views
    2,550

    The way I see it if it simply fell apart it...

    The way I see it if it simply fell apart it shouldn't be difficult to reassemble. I don't mind cleaning everything and adding new grease. There is no reason why adding fresh grease will harm...
  12. Replies
    6
    Views
    2,550

    Driveshaft joint- ball bearing (re)assembly

    While reinstalling the driveshaft the cap fell off the rear joint and a couple bearings fell out. After trying for 45 minutes to reassemble the joint I'm taking a break and hoping someone can...
  13. Replies
    0
    Views
    1,028

    Wrapping up tranny swap, starter question:

    Are there 2 red wires that connect to the starter post? I neglected to reconnect the wiring for the starter before installing the subframe. I honestly don't recall if I removed one or two from the...
  14. Replies
    2
    Views
    1,446

    Thanks for the response. It's giving me a hard...

    Thanks for the response. It's giving me a hard time. Do the rails have to be slid simultaneously or can you slide one a little then the other? I'm really going to have to fab a small tool of some...
  15. Replies
    2
    Views
    1,446

    Engine removal- wiring harness

    I'm dropping the engine in my 00 xc in order to install a used and hopefully properly functioning transmission. I would prefer to simply disconnect the main wiring harness and pull it along with the...
  16. Replies
    3
    Views
    1,601

    Thank you sir!

    Thank you sir!
  17. Replies
    3
    Views
    1,601

    Tranny front pump removal

    I goofed and didn't have the correct alignment when installing the transmission to the engine with torque converter. I think I crashed the front pump. I'm in the process of swapping the unit from...
  18. Replies
    5
    Views
    1,916

    Much appreciated!

    Much appreciated!
  19. Replies
    5
    Views
    1,916

    Bevel gear out, seals question:

    Since I'm in the process of swapping transmissions on my 00 xc I feel it's a good idea to replace the seals on the bevel gear. Anyone happen to have the part numbers and a good source? I was...
  20. Thanks for the advice fellas. I think I will...

    Thanks for the advice fellas. I think I will attempt the method of suspending the engine, dropping the subframe, and pulling the tranny. That way I won't have to deal with draining the coolant and...
  21. Do I have to pull the motor to remove the tranny or can I drop it from below?

    I've not had any luck locating a transmission removal tutorial. What is the best approach for removal? It looks like there is not enough clearance to slide it out the drivers side and the subframe...
  22. Replies
    6
    Views
    3,745

    I removed and cleaned two sensors. Both had...

    I removed and cleaned two sensors. Both had accumulated metal shavings and greasy residue. I took it for a drive and the flashing arrow and check engine light came on in less than 2 minutes. I...
  23. I actually pulled the lower 2 bolts to check for...

    I actually pulled the lower 2 bolts to check for fluid on the ends. There wasn't any. I think the oil accumulates there after leaking past a seal above.
  24. Replies
    6
    Views
    3,745

    Thanks guys! I'll check the sensor and report...

    Thanks guys! I'll check the sensor and report back. Is there a check I can perform with a multi-meter to determine if the sensor is within spec?
    The car runs and drives fine until I reach 55+mph. ...
  25. Replies
    6
    Views
    3,745

    Transmission interchangeability

    I picked up a 2000 V70 xc se with a snapped timing belt. I pulled the trouble codes prior to the head replacement and they were:
    p0756 shift solenoid b ckt performance or stuck off
    P0722 output...
Results 1 to 25 of 38
Page 1 of 2 1 2